manualshive.com logo in svg

Jung ZLLA5004M, Operating Instructions Manual

Share
Download
Jung ZLLA5004M Operating Instructions Manual Download Page 10

Figure 13

o

Keep the 

Ƈ

 and 

ƈ

 buttons pressed until the LEDs flash green.

Lamp flashes: Reset in progress.
LEDs light up green; lamp lights up. Resetting successful.
LEDs flash red quickly for 3 seconds. Participant could not be reset.

4.6 Deleting connections from the transmitter to the luminaires

i

The transmitter can save a maximum of 10 connections to luminaires. If the memory is full,
a connection needs to be deleted first in order to be able to save a new connection.

Figure 14

o

Press 

Ɔ

 and 

ƍ

 buttons simultaneously and briefly until the connection to be deleted

is selected.
LEDs light up red. All connections to luminaires are selected.

o

Press the 

Ɔ

 and 

ƍ

 buttons simultaneously and briefly until the connection to be

deleted is selected.
The corresponding luminaire flashes.

i

If the corresponding luminaire is defective or does not exist any more, press the 

Ɔ

 or

ƍ

 buttons simultaneously until to luminaire flashes after pressing. The transmitter will

indicate this by an LED flashing in red.

o

Press the 

Ƈ

 and 

ƈ

 buttons simultaneously for longer than 4 seconds.

LEDs light up green for 3 seconds. The connection has been deleted from the transmitter.

10/17

32596203
J0082596203

23.05.2016

ZigBee radio transmitter module 4-gang

Summary of Contents for ZLLA5004M


















Reviews:

No comments

Brands by name

Popular brands

Load more brands