JUMO 00725428 Operating Manual Download Page 5 | Manualshive

Page: 5 / 36

JUMO 00725428 Operating Manual Download Page 5

5

1 Introduction

1

Introduction

1.1

Safety information

General

This manual contains information that must be observed in the interest of your own safety and to avoid
material damage. This information is supported by symbols which are used in this manual as indicated.
Please read this manual before starting up the device. Store this manual in a place that is accessible to
all users at all times.
If difficulties occur during startup, please do not intervene in any way that could jeopardize your warranty
rights!

Warning symbols

CAUTION!

This symbol in connection with the signal word indicates that

material damage or data loss

will occur

if the respective precautionary measures are not taken.

Note symbols

NOTE!

This symbol refers to

important information

about the product, its handling, or additional benefits.

READ THE DOCUMENTATION!

This symbol, which is attached to the device, indicates that the associated

documentation for the de-

vice

must be

observed

. This is necessary to identify the nature of the potential hazard, and to take

measures to prevent it.

REFERENCE!

This symbol refers to

additional information

in other sections, chapters, or other manuals.

DISPOSAL!

At the end of its service life, the device and any batteries present do not belong in the trash! Please en-
sure that they are

disposed of

properly and in an

environmentally friendly

manner.

«
...
3
4
5
6
7
...
»

Summary of Contents for 00725428





































Reviews:

No comments