JUMO 00725428 Operating Manual Download Page 11 | Manualshive

Page: 11 / 36

JUMO 00725428 Operating Manual Download Page 11

11

3 Mounting

3

Mounting

The cable transmitter may only be installed, connected and started up by qualified and authorized per-
sonnel observing these operating instructions, the applicable standards, and the legal requirements (de-
pending on the application).
If you experience difficulties during installation and startup, please contact the manufacturer.
The device can be installed in any position.

NOTE!

The cable transmitter is not suitable for safety-critical applications.

NOTE!

The cable transmitter is not suitable for installation and application in potentially explosive areas.

NOTE!

The cable transmitter and the connected temperature sensor must be connected to the potential equal-
ization system of the plant via the process connection. Suitable shielded lines must also be used to en-
sure continuous shielding.

Mounting the cable transmitter

Insert the cable transmitter into the corresponding connecting cable and tighten it by hand.

«
...
9
10
11
12
13
...
»

Summary of Contents for 00725428





































Reviews:

No comments