Johnson Controls YORK OPTIVIEW CONTROL CENTER Operation Manual Download Page 21

Page: 21 / 142

JOHNSON CONTROLS

SECTION 2 - OPTIVIEW OPERATION

FORM 160.10-O1

ISSUE DATE: 4/27/2018

Condenser Pressure

This display indicates the refrigerant pressure in the

condenser.

Condenser Saturation Temperature

This display indicates the saturation temperature in the

condenser.

Oil Sump Temperature

This displays the temperature of the oil in the sump.

Oil Pressure

This display indicates the pressure differential between

the high side oil pressure transducer (output of oil

filter) and the low side oil pressure transducer (com-

pressor housing). The displayed value includes offset

pressure derived from auto-zeroing during the system

prelube. If either of the transducers used to calculate

this differential are out of range, the display field will

show XX.X.

% Full Load Amps

This displays the percentage of full load amps utilized

by the system.

Current Limit

This display indicates the current limit value in use.

This value could come from a 0-20mA, 4-20mA,

0-10VDC or 2-10VDC input in analog remote mode,

PWM signal in digital remote mode, MicroGateway

interface in ISN (Integrated Systems Network) mode,

or a locally programmed value.

PROGRAMMABLE

None

NAVIGATION
Home

Access Level Required: VIEW

Returns the display to the Home screen.

Summary of Contents for YORK OPTIVIEW CONTROL CENTER















































































































































Search results

Summary of Contents for YORK OPTIVIEW CONTROL CENTER

Reviews:

Related manuals for YORK OPTIVIEW CONTROL CENTER

Brands by name

Popular brands

Johnson Controls YORK OPTIVIEW CONTROL CENTER, Operation Manual

Search results

Summary of Contents for YORK OPTIVIEW CONTROL CENTER

Reviews:

Related manuals for YORK OPTIVIEW CONTROL CENTER

Brands by name

Popular brands