manualshive.com logo in svg

Johnson Controls Frick QUANTUM LX, Setup

Share
Download
Johnson Controls Frick QUANTUM LX Setup Download Page 112

QUANTUM™ LX COMPRESSOR CONTROL PANEL

COMMUNICATIONS SETUP

090.020-CS (APRIL 13)

Page 112

Q5 SERIAL COMMUNICATIONS PORT WIRING

GENERAL NOTE

The information that is presented here and on the 

following pages, refers to the Interface board and not 

the Q5 board. The Interface board was developed to 

make customer connections to the processor easier, 

as the Q5 use connections that are too small and del-

icate to easily utilize in the 

fi

 eld.

RS-232 WIRING AND JUMPERS

With the introduction of the Q5/Interface board, cus-

tomer connections to RS-232 have been eliminated. 

If RS-232 communications IS required, these signals 

may be converted to RS-422/485, and the appropriate 

available port(s) utilized.

RS-422/485 WIRING AND JUMPERS

All four Interface board serial communications ports 

are capable of RS-485, and COMM-1 (P10) and 

COMM-2 (P11) can additionally be con

fi

 gured as ei-

ther RS-422 or RS-485.

The following table describes the Interface board RS-

422 connector pinouts and their associated commu-

nications signals: 

RS-422 Signal Wiring

Connector 

Pin #

Signal

COMM-1

(P10)

COMM-2

(P11)

5

GND

GND

4

TX+

TX+

3

TX-

TX-

2

RX+

RX+

1

RX-

RX-

 

RS-485 Signal Wiring

Connector 

Pin #

Signal

COMM

1

(P10)

COMM

2

(P11)

COMM

3

(P17)

COMM

4

(P16)

5

GND

4

N/C

3

N/C

GND

2

+TX/+RX

+TX/+RX

1

 -TX/-RX

 -TX/-RX

The following pictorial shows a cutaway view of the 

Interface board, as well as the jumpers, LED’s and 

signal pinouts to allow the end user to communi-

cate to COMM-1 (P10) and COMM-2 (P11) using RS-

422/485 protocol, and to use COMM-3 (P16) to com-

municate via RS-485. 

NOTE: 

COMM-3 and COMM-4 

do not have any associated jumpers, and COMM-4 

(P17) is reserved for I/O board communications. Refer 

to the tables in this section for the speci

fi

 cs on the 

jumper settings RS-422/485:

COMM-1

(P10)

RS-422

GND

+TX

-TX

+RX

-RX

RS-485

N/C

N/C

GND

+TX/+RX

-TX/-RX

COMM-2

(P11)

RS-422

GND

+TX

-TX

+RX

-RX

RS-485

N/C

N/C

GND

+TX/+RX

-TX/-RX

COMM-4

(P17)

RS-485

(RESERVED)

COMM-3

(P16)

RS-485

GND

+TX/+RX

-TX/-RX

RS-422/485 Connectors, Jumpers and LED Location

RS-422/485 (COMM-1, & COMM-2, P11) Board Jumpers

 

Jumper Title

Function

Jumper Setting

COMM-1

(P10

COMM-2

(P11)

J1

J7

RS-422 (4-Wire)

Default

 

3  

 

2  

 

1 

1 - 2 

Closed

RS-485

(2-Wire)

 

3

 

 

2

 

 

1 

2 - 3 

Closed

J2

J13

Pull Down

Default

 

1 Pin 

Only

J3

J16

Pull Up

Default

 

1 Pin 

Only

J5

J17

RS-422

Default

 

1 Pin 

Only

RS-485

1 - 2 

Closed

J6

J18

RS-422

Default

 

1 Pin 

Only

RS-485

1 - 2 

Closed

J4

J22

High Speed Target

Default

1 - 2 

Closed

NOTE: 

The triangle symbol (

 

 ) denotes Pin 1 on con-

nectors. 

Summary of Contents for Frick QUANTUM LX













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands