manualshive.com logo in svg

JLG 3507, Supplemental Repair Manual, Page: 7 / 180

Share
Download
JLG 3507 Supplemental Repair Manual Download Page 7

5

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

NORMAL DIFFERENTIAL UNIT ........................................................................................................ 125

EXPLODED VIEW .......................................................................................................................................... 125
DISASSEMBLY ............................................................................................................................................. 126
ASSEMBLY ................................................................................................................................................... 128
SPECIAL TOOLS  .......................................................................................................................................... 131

T1 ............................................................................................................................................................. 131
T2 ............................................................................................................................................................. 131
T3 ............................................................................................................................................................. 132
T4 ............................................................................................................................................................. 132

LIMITED SLIP DIFFERENTIAL UNIT (25% AND 45%) .................................................................... 133

EXPLODED VIEW .......................................................................................................................................... 133
DISASSEMBLY ............................................................................................................................................. 134
ASSEMBLY ................................................................................................................................................... 137
SPECIAL TOOLS  .......................................................................................................................................... 140

T1 ............................................................................................................................................................. 140
T2 ............................................................................................................................................................. 140
T3 ............................................................................................................................................................. 141
T4 ............................................................................................................................................................. 141

HYDRAULIC DIFFERENTIAL LOCK ................................................................................................. 143

EXPLODED VIEW .......................................................................................................................................... 143
DISASSEMBLY ............................................................................................................................................. 144
ASSEMBLY ................................................................................................................................................... 147
SPECIAL TOOLS  .......................................................................................................................................... 149

T1 ............................................................................................................................................................. 149
T2 ............................................................................................................................................................. 149

HYDRAULIC NEGATIVE BRAKE  ...................................................................................................... 151

EXPLODED VIEW .......................................................................................................................................... 151
DISASSEMBLY ............................................................................................................................................. 152
ASSEMBLY ................................................................................................................................................... 155

INCORPORATED REDUCTION GEAR AND PINION 602  ............................................................... 161

EXPLODED VIEW .......................................................................................................................................... 161
DISASSEMBLY ............................................................................................................................................. 162
ASSEMBLY ................................................................................................................................................... 166
SPECIAL TOOLS  .......................................................................................................................................... 169

T1 ............................................................................................................................................................. 169
T2 ............................................................................................................................................................. 170
T3 ............................................................................................................................................................. 171
T4 ............................................................................................................................................................. 172
T5 ............................................................................................................................................................. 173
T6 ............................................................................................................................................................. 174

Summary of Contents for 3507





















































































































































































Reviews:

No comments