JLG 3507 Supplemental Repair Manual Download Page 115

Page: 115 / 180

DISASSEMBLY

113

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

Hold piston (12) as it may be rapidly ejected and damaged.

FIGURE 7:

Remove check screws (17) from cylinder (18).

FIGURE 8:

Remove cylinder (18) complete with guide pin (19)

of piston (12).

NOTE:

Take note of direction of assembly.

FIGURE 9:

With the help of a lever, pry off the cover (23) com-

plete with o-ring (24).

CAUTION

NOTE:

Thoroughly clean the face of bevel pinion support where
the hub rests, check the o-ring (24) and replace it if ne-
cessary.

FIGURE 10:

Remove friction discs (25), (26) and hub (27).

FIGURE 11:

3-FUNCTION VERSION ONLY

Loosen nuts (28) and unscrew studs (29) to retract the
adjustment points (30).
ONLY IF NECESSARY. Remove points (30).

NOTE:

Loosen studs (29) in an alternate manner until the piston
comes to end of backstroke.

25 26

28 29

Summary of Contents for 3507





















































































































































































Search results

Summary of Contents for 3507

Reviews:

JLG 3507, Supplemental Repair Manual, Page: 115 / 180

Search results

Summary of Contents for 3507

Reviews: