JLG 3507 Supplemental Repair Manual Download Page 157

Page: 157 / 180

ASSEMBLY

155

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

ASSEMBLY

FIGURE 16:

Fit o-rings (4)(28)(27)(5)(6) onto the piston (3).

Lubricate the piston and the o-rings and install the unit into
the cylinder (7).

FIGURE 17:

Using a plastic hammer, insert the piston (3) into

the cylinder (7).

NOTE:

Lightly hammer all around the edge in an alternate se-
quence.

FIGURE 18:

Fit o-rings (9) and (8) onto the piston (10).

Lubricate the piston and the o-rings and install the unit into
the cylinder (7).

FIGURE 19:

Using a plastic hammer, insert the piston (10)

into the cylinder (7).

NOTE:

Lightly hammer all around the edge in an alternate

sequence.

FIGURE 20:

Apply grease and position the Belleville washers

(2) and engage the cylinder (7).

NOTE:

Check the sense of direction of washers (7) and relative
centering.

Summary of Contents for 3507





















































































































































































Search results

Summary of Contents for 3507

Reviews:

JLG 3507, Supplemental Repair Manual, Page: 157 / 180

Search results

Summary of Contents for 3507

Reviews: