JLG 3507 Supplemental Repair Manual Download Page 123

Page: 123 / 180

ASSEMBLY

121

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

FIGURE 50:

Fit the electronic sensor (1) and screw it up to the

limit stop. Unscrew sensor by 3/4 turn and lock into position
with nut. Locking torque: maximum 30 N·m.

Do not exceed the specified torque setting.

FIGURE 51:

To release the negative brake during an emer-

gency, (lack of pressure due to vehicle breakdown), loosen
nuts (22) and screw studs (21) in an alternate and gradual
manner until you notice some preloading;
continue by giving another 1.5 turns.

8÷

1,2mm

CAUTION

21 22

FIGURE 52:

When the emergency is over, loosen the studs in

an alternate manner until a 17 mm projection is obtained; lock
into position with the nuts (22) tightened to 15 N·m.

Summary of Contents for 3507





















































































































































































Search results

Summary of Contents for 3507

Reviews:

JLG 3507, Supplemental Repair Manual, Page: 123 / 180

Search results

Summary of Contents for 3507

Reviews: