background image

1

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be followed, including the 

following:
This Serger/Overlocker/Overlock machine is designed and manufactured for household use only.
Read all instructions before using this Serger/Overlocker/Overlock machine.

DANGER

— 

To reduce the risk of electric shock:

 1.  An appliance should never be left unattended when plugged in. Always unplug  

   this 

Serger/Overlocker/Overlock

 machine from the electric outlet immediately after 

    using and before cleaning.

WARNING

 To reduce the risk of burns, fire, electric shock, or injury to persons:

  1.  Do not allow to be used as a toy. Close attention is necessary when this Serger/Overlocker/Overlock

    machine is used by or near children.

  2.  Use this appliance only for its intended use as described in this owner’s manual.

    Use only attachments recommended by the manufacturer as contained in this owner’s manual.

  3.  Never operate this Serger/Overlocker/Overlock machine if it has a damaged cord or plug, if it is not  

    working properly, if it has been dropped or damaged, or dropped into water.

    Return this Serger/Overlocker/Overlock machine to the nearest authorized dealer or service center  

    for examination, repair, electrical or mechanical adjustment.

  4.  Never operate the appliance with any air opening blocked. Keep ventilation openings of this   

  Serger/Overlocker/Overlock machine and foot controller free from accumulation of lint, dust and  

    loose cloth.

  5.  Never drop or insert any object into any opening.

  6.  Do not use outdoors.

  7.  Do not operate where aerosol (spray) products are being used or where oxygen is being 

        administered.

  8.  To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

  9.  Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

 10.  Keep fingers away from all moving parts. Special care is required around the 

Serger/Overlocker/ 

   Overlock machine needle and/or cutting blade.

 11.  Always use the proper needle plate. The wrong plate can cause the needle to break.

 12.  Do not use bent needles.

 13.  Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

 14.  Switch  this  Serger/Overlocker/Overlock

 machine off (“O”) when making any adjustment in the  

    needle area, such as threading the needle, changing the needle or changing the presser foot, and  

    the like.

 15.  Always unplug this Serger/Overlocker/Overlock machine from the electrical outlet when removing  

    covers, lubricating, or when making any other adjustments mentioned in this owner’s manual.

SAVE THESE INSTRUCTIONS

Please note that on disposal, this product must be safely recycled in accordance with relevant 

National legislation relating to electrical/electronic products. If in doubt please contact your 

retailer for guidance. (European Union only)

For Europe only:

This appliance can be used by children aged from 8 years and above and persons with reduced 

physical, sensory or mental capabilities or lack of experience and knowledge if they have been given 

supervision or instruction concerning use of the appliance in a safe way and understand the hazards 

involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made 

by children without supervision.

For outside Europe (except U.S.A and Canada):

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 

instruction concerning use of the appliance by a person responsible for their safety. 

Children should be supervised to ensure that they do not play with the appliance.

Summary of Contents for AT2000D


































































Reviews: