28
Инструкция |
Пила цепная бензиновая
RUS
гаечного ключа (18).
Элементы инструмента и свечи зажигания
•
очистите от нагара (26).
Проверьте или установите (в
•
случае необходимости) зазор
между электродами и свечей
зажигания (зазор должен быть
равен 0, 7-0,8 мм).
Установить свечу зажигания
•
(26) и повторно собрать свечу
зажигания; затем все шаги должны
быть выполнены в обратной
последовательности, как описано в инструкции.
Проверка
автоматического
смазочного
механизма
28. Регулировочный винт
Проверку
автоматического
смазочного
механизма можно осуществить следующим
образом:
Включить машину и движущуюся часть
•
инструмента расположите на картонную бумагу.
ПРИМЕЧАНИЕ:
•
не касайтесь с цепью,
сохраняйте
безопасное
расстояние
приблизительно 20 см. Если на картоне или на
бумаге заметили следы масла, то автоматический
смазочный механизм работает правильно. Если,
несмотря на полный масляный бочок не видно
на бумаге никакие признаки масляной смазки, то
нужно устранить дефект инструмента согласно
данной инструкции или консультируйтесь с
центром обслуживания IVT.
Подачу
•
с м а з ы в а ю щ е й
жидкости на цепь
(1)
можно
регулировать с
п о м о щ ь ю
р е г у л и р о в о ч -
ного винта (28).
П о в е р н и т е
регулировочный
винт (28) против
часовой стрелки,
чтобы увеличить подачу жидкости, по часовой
стрелке, чтобы уменьшить (обратите внимание
на
знаки,
изображенные
на
корпусе
инструмента).
Заточка цепи.
Заточку цепи может сделать квалифицированный
мастер в любом центре обслуживания IVT.
Длительное хранение
Если инструмент оставляете на длительное
время, вылить из масляного бочка жидкость и
высушите бочок, а пильную цепь (1) и пильную
шину (2) подержите в масляной ванне в течение
короткого времени, а затем обертывайте их в
смазанной бумаге.
Чистота
в
обслуживании
должна
быть
обязательным условием для долгосрочного и
безопасного обслуживания машины.
В случае, если, несмотря на тщательную
проверку
производителем
технических
свойств инструмента в процессе производства,
инструмент вышел из строя, все ремонтные
работы
должны
выполняться
только
квалифицированными специалистами IVT.
ПРИМЕЧАНИЕ: при обращений в
центр обслуживания IVT пожалуйста
оставьте 1/3 объема масла и топливо
в баках.
Защита окружающей среды
Вторичное
использование
сырья
вместо выбрасывания eгo в мусор!
Инструмент, дополнительные принадлежности
и упаковку следует экологически чисто
утилизировать.
В интересах чистосортной рециркуляции
отходов, детали из синтетических материалов
соответственно обозначены.
Настоящее руководство по эксплуатации
напечатано на бумаге, изготовлено из вторичного
сырья без применения хлора.
0.7 - 0.8 mm
28
Summary of Contents for GCHS-38
