27
Инструкция |
Пила цепная бензиновая
RUS
A
C
B
Не
распиливать
брусок
либо
обрабатываемый
материал
полностью!
Приблизительно 1/10 диаметра ствола дерева
•
нужно оставить не распиленным. Если дерево
начинает падать, удалите машину от дерева и
отойдите назад либо в сторону.
Рабочая зона вокруг дерева должна быть
•
свободной от препятствий: рабочая зона должна
позволять свободное перемещение рабочего
оператора.
При
горизонтальном
распиле
работа
•
инструмента должно завершаться до метки (C).
При завершений распила дерева опасайтесь
•
от падающих ветвей.
Обслуживание и хранение
Прежде, чем выполнять ремонтные
работы отключите кабель из сети.
Чистка инструмента
Очищайте корпус инструмента и вентиляционных
отверстий от опилок и деревянной стружки,
а также и вентиляционных отверстий. Не
используйте едкие вещества или растворители
для очистки инструмента. Избегайте любого
промасливания поверх корпуса инструмента.
Очистка фиксатора тормоза цепи.
При работе с пильной цепью (1)
надевать защитные перчатки.
Положить
инструмент
на
плоскую
•
поверхность.
Отвинтить гайку (19) с помощью гаечного
•
ключа (18), переместите Фиксатор тормоза цепи
(4) в предельное свободное положение и извлечь
защитное устройство (20).
Извлечь фиксатор тормоза цепи.
•
Извлечь пильную цепь (1) и отвинтить
•
пильную шину (2).
Очистить от опилок и деревянных стружек
•
цепь (1) и место пильной шины (2).
Смазать цепь (1) и пильную шину (2), чтобы
•
защитить их от быстрого износа.
Установить
материал
распиловки
•
вышеуказанным методом.
Завернуть корпус и защитный кожух цепи
•
(10) бумагой, либо положить в оригинальную
упаковку.
Очистка фильтра
25. Фильтр
Очищайте
•
воздушный фильтр
после каждых 50
часов работы.
Положите
•
инструмент
на плоскую
поверхность.
Ослабить
•
специальную
гайку (6) и снимите
корпус (7).
Очистить
•
фильтр (25) спиртом.
Вытереть фильтр (25) сухой и мягкой тряпкой
•
либо салфеткой.
Установите фильтр (25).
•
Установить
корпус
(7)
и
закрепить
•
специальную гайку (6).
Проверка свечи зажигания
26. Свеча
зажигания
27. Головка
свечи
зажигания
Положите
инструмент
на
плоскую
•
поверхность.
Ослабить специальную гайку (6) и снимите
•
корпус (7).
Снять головку свечи зажигания (27) из свечи
•
зажигания (26).
Отвинтить свечу зажигания (26) с помощью
•
25
26
27
Summary of Contents for GCHS-38
