IS5COM IES26G Series User Manual Download Page 38

Page: 38 / 79

iES26G Series User’s Manual

iS5 Communications Inc.

4.1.8.2

SNMP –Trap Setting

The SNMP Service, when configured for an agent, generates trap messages that are sent to a

trap destination, if any specific events occur. For example, you can configure the SNMP

service to send a trap when it receives a request for information that does not contain the

correct community name and does not match an accepted host name for the service.

SNMP Trap Setting interface

The following table describes the labels for the Trap Setting screen.

Label

Description

IP Address

The server IP address to receive Trap.

Community

Community for authentication.

Trap Version

Trap Version supports V1 and V2c.

Add

Add trap server profile.

Remove

Remove trap server profile.

Help

Show help file.

4.1.8.3

SNMP – SNMPv3 Setting

SNMPv3 Setting interface

Summary of Contents for IES26G Series
















































































Search results

Summary of Contents for IES26G Series

Reviews:

Related manuals for IES26G Series

Brands by name

Popular brands

IS5COM IES26G Series, User Manual

Search results

Summary of Contents for IES26G Series

Reviews:

Related manuals for IES26G Series

Brands by name

Popular brands