manualshive.com logo in svg

Intel SR2600UR - Server System - 0 MB RAM, Service Manual

Share
Download
Intel SR2600UR - Server System - 0 MB RAM Service Manual Download Page 25

Intel

®

 Server System SR2600UR/SR2625UR Service Guide

5

Hardware (peripheral 

boards, adapter cards) 

and operating systems 

that have been tested with 

this product

Processors that have 

been tested with this 

product

DIMMs that have been 

tested with this product

Hard Drives that have 

been tested with this 

product

Server Configurator Tool

Available at: 

http://serverconfigurator.intel.com/default.aspx

Latest drivers, firmware 

updates (BIOS, BMC, 

FRUSDR), and utilities

Available for download at:

http://support.intel.com/support/motherboards/server/s5520ur/

Click the “Software and Drivers” link on the left side of the web 

page.

To make sure your system 

falls within the allowed 

power budget

Power Budget Analysis Tool

Available at:

http://support.intel.com/support/motherboards/server/s5520ur/

For software to manage 

your Intel

®

 server

Intel

®

 System Management Software

Available at:

http://www.intel.com/go/servermanagement/

Table 1. Server System References

For this information or 

software

Use this Document or Software

Summary of Contents for SR2600UR - Server System - 0 MB RAM











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands