manualshive.com logo in svg

Intel SR2600UR - Server System - 0 MB RAM, Service Manual

Share
Download
Intel SR2600UR - Server System - 0 MB RAM Service Manual Download Page 11

Intel

®

 Server System SR2600UR/SR2625UR Service Guide

xi

Removing and Installing the Small Air Baffle (Intel

®

 Server System SR2600UR only)  .......66

Removing the Small Air Baffle .....................................................................................66
Installing the Small Air Baffle .......................................................................................66

Removing and Installing the Fan Baffle  ...............................................................................67

Removing the Fan Baffle  .............................................................................................67
Installing the Fan Baffle  ...............................................................................................69

Removing and Installing the Large Air Baffle .......................................................................70

Removing the Large Air Baffle .....................................................................................70
Installing the Large Air Baffle .......................................................................................70

Installing and Removing a Hot-swap Hard Drive (Intel

®

 Server System SR2600UR only)  .71

Installing a SAS or SATA Hot-swap Hard Disk Drive  ..................................................71
Removing a SAS or SATA Hot-swap Hard Disk Drive ................................................74

Installing and Removing a Hot-swap 2.5 inch Hard Drive (Intel

®

 Server System SR2625UR 

only) .............................................................................................................................74
Installing a Hot-swap SAS/SATA Hard Disk Drive  ......................................................74
Removing a Hot-swap SAS/SATA Hard Disk Drive  ....................................................76

Installing or Removing a Slimline Optical Drive or Internal USB Floppy (Intel

®

 Server System 

SR2600UR only) ..........................................................................................................77
Installing a Slimline Optical Drive or Internal USB Floppy ...........................................78
Removing a Slimline Optical Drive or Internal USB Floppy .........................................80

Installing or Removing a Slimline Optical Drive (Intel

®

 Server System SR2625UR only)  ...82

Installing a Slimline Optical Drive  ................................................................................82
Removing a Slimline Optical Drive  ..............................................................................83

Installing a Tape Drive  .........................................................................................................84
Installing a Sixth Hard Disk Drive (Intel

®

 Server System SR2600UR only) .........................86

Installing the 2.5 Inch Fixed Hard Disk Drives  .....................................................................90
Filling Empty Server System Bays (Intel

®

 Server System SR2600UR only)  .......................94

Filling Empty Server System Bays (Intel

®

 Server System SR2625UR only)  .......................95

Installing and Removing the I/O Expansion Module  ............................................................96

Installing the I/O Expansion Module  ............................................................................96
Removing the I/O Expansion Module  ..........................................................................97

Installing and Removing the Intel

®

 Remote Management Module 3  ...................................98

Installing the Intel

®

 RMM3 ...........................................................................................98

Removing the Intel

®

 RMM3 .......................................................................................101

Replacing the Midplane Board ...........................................................................................102

Removing the Midplane Board  ..................................................................................102
Installing the Midplane Board  ....................................................................................104

Replacing the Backplane  ...................................................................................................107

Removing the Backplane ...........................................................................................107
Installing the Backplane .............................................................................................109

Installing and Removing the RAID Activation Key and the RAID Mini-DIMM (Active Systems 

Only) ..........................................................................................................................111
Installing the RAID Activation Key and the RAID Mini-DIMM  ....................................111
Removing the RAID Activation Key and the RAID Mini-DIMM  ..................................112

Summary of Contents for SR2600UR - Server System - 0 MB RAM











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands