manualshive.com logo in svg

Intel SR2600UR - Server System - 0 MB RAM, Service Manual

Share
Download
Intel SR2600UR - Server System - 0 MB RAM Service Manual Download Page 113

Intel

®

 Server System SR2600UR/SR2625UR Service Guide

93

4. Slide the filler panel containing the installed 2.5 hard disk drives into the system 

until it clicks into place as shown in 

Figure 84

.

Figure 84. Installing the 2.5 inch fixed HDD assembly

5. Connect one end of the power cable to the SAS/SATA connector on the back side of 

the backplane (see letter “A” in 

Figure 85

).

6. Connect the other end of the power cable to the two hard disk drives (see letter “B” 

in 

Figure 85

).

7. Connect one end of the data cables to the SATA connectors on the server board (see 

letter “C” in 

Figure 85

) or SAS/SATA connectors on an SAS/SATA add-in PCI 

card.

AF003037

A

B

Summary of Contents for SR2600UR - Server System - 0 MB RAM











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands