Thermal/Mechanical Specifications and Design Guidelines
85
Mechanical Drawings
Figure B-10. Reference Clip (Sheet 1 of 2)
1
3
4
5
6
7
8
B
C
D
A
1
2
3
4
5
6
7
8
B
C
D
A
A
A
SHEET
1 OF
2
DO NOT SCALE DRAWING
SCALE:
3:1
01
E36830
D
REV
DRAWING NUMBER
CAGE CODE
SIZE
HAVENDALE POWER ON SAMPLE
HEAT SINK CLIP
TITLE
2200 MISSION COLLEGE BLVD. P.O. BOX 58119 SANTA CLARA, CA 95052-8119
CORP.
R
PST
DEPARTMENT
SEE NOTES
FINISH:
SEE NOTES
MATERIAL:
-
-
DATE
APPROVED BY
-
-
DATE
CHECKED BY
02/04/08
KG TAN
DATE
DRAWN BY
04/02/03
R. AOKI
DATE
DESIGNED BY
UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN MILLIMETERS. TOLERANCES: LINEAR
.15
ANGLES:
1
INTERPRET DIMENSIONS AND TOLERANCES PER ANSI Y14.5M-1994
THIRD ANGLE PROJECTION
REVISION HISTORY
ZONE
REV
DESCRIPTION
DATE
APPROVED
A
RELEASE FOR PROTOTYPING
02/04/08
N
A
E36830
1
A
DWG. NO
SHT.
REV
PARTS LIST
DESCRIPTION
PART NUMBER
ITEM NO
QTY PER ASSY
-001
-002
-003
CLIP, STEEL, STAMPED
E36830-001
TOP
7
4.22
0.2
.166
.007
[]
98.8 3.890[]
98.8 3.890[]
2
0.2
.079
.007
[]
SQ
53.5
0.2
2.106
.007
[]
4X
10
0.2
.394
.007
[]
41.73 1.643[]
B
7
33.86
0.2
1.333
.007
[]
A
()1.60
.063[]
NOTES:
1. THIS DRAWING TO BE USED IN CONJUNTION WITH SUPPLIED 3D DATABASE FILE. ALL DIMENSIONS AND TOLERANCES ON THIS DRAWING TAKE PRECEDENCE OVER SUPPLIED FILE AND ARE APPLICABLE AT PART FREE, UNCONSTRAINED STATE UNLESS INDICATED OTHERWISE. 2. MATERIAL: A) TYPE: AISI 1065 COLD DRAWN STEEL OR EQUIVALENT 1.6MM THICKNESS
.02 [.063"]
B) CRITICAL MECHANICAL MATERIAL PROPERTIES FOR EQUIVALENT MATERIAL SELECTION: ELASTIC MODULUS > 206.8 GPA [29,900 KSI] MIN TENSILE YIELD STRENGTH (ASTM D638) > 380 MPa [55KSI] C) MASS - 37.7 GRAMS (REF) 3. SECONDARY OPERATIONS: A) FINISH: NICKEL PLATE REQUIRED AFTER FORMING 4. ALL DIMENSIONS AND TOLERANCES ARE SHOWN AFTER PLATING
5
PUNCH DIRECTION
6. BREAK ALL SHARP CORNERS AND BURRS
7
CRITICAL TO FUNCTION DIMENSION
8
COINING REQUIRED AS SPECIFIED
9. SECONDARY UNIT TOLERANCES SHOULD BE CALCULATED FROM PRIMARY UNITS TO AVOID ROUND OFF ERROR.
7
0.5 [.01]
A
B
7
0.5 [.01]
A
B
SEE DETAIL
A
REMOVE ALL BURRS OR SHARP EDGES AROUND PERIMETER OF PART. SHARPNESS OF EDGES SUBJECT TO HANDLING ARE REQUIRED TO MEET THE UL1439 TEST.
PERMANENTLY MARK PART NUMBER AND REVISION LEVEL APPROXIMATELY WHERE SHOWN XXXXXX-XXX REV XX
SECTION
A-A
SEE DETAIL
B
SEE DETAIL
C
SEE DETAIL
D
SEE DETAIL
A
SEE DETAIL
B
SEE DETAIL
C
SEE DETAIL
D
Summary of Contents for i5-700
