manualshive.com logo in svg

Integral Technologies Dvx 1000, User Manual, Page: 120 / 137

Share
Download
Integral Technologies Dvx 1000 User Manual Download Page 120

116

The DVXMonitor tab contains the following options (see Figure 57):

•

Disable DVXMonitor—

disables DVXMonitor’s ability to watch for fail-

ure conditions.

•

Time Before Reboot (Minutes)—

the amount of time between the occur-

rence of a restart situation (such as MasterControl failure) and the sys-
tem restarting.

•

Minimum Latch Time (Seconds)—

the minimum amount of time that the

alarm output is triggered when a selected event occurs. The alarm is trig-
gered for a longer amount of time only if the alarm event duration ex-
ceeds the minimum latch time.

•

Reset Alarm Output—

forces the trigger to its normal state (closed). This

overrides the Minimum Latch Time.

•

Latch Until Forced—

causes the alarm output to remain activated when a

selected event occurs, until Reset Alarm Output is selected.

•

Alarm Scheduling—

a schedule of when the DVX 1000 system is moni-

tored for failure by DVXMonitor.

Figure 57

The DVXMonitor
plug-in allows you
to configure DVX
1000 to trigger the
alarm output when
certain conditions
or actions occur.

Summary of Contents for Dvx 1000










































































































































Reviews:

No comments