49
En
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The
volume of each speaker can be set (
➔
page 48
).
■
Equalizer
`
Manual
:
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
`
Off
:
Tone off, response flat.
Note
• You can select: “
25Hz
”, “
40Hz
”, “
63Hz
”, “
100Hz
”, “
160Hz
”,
“
250Hz
”, “
400Hz
”, “
630Hz
”, “
1000Hz
”, “
1600Hz
”,
“
2500Hz
”, “
4000Hz
”, “
6300Hz
”, “
10000Hz
” or “
16000Hz
”.
And for the subwoofer, “
25Hz
”, “
40Hz
”, “
63Hz
”, “
100Hz
”, or
“
160Hz
”.
• When the Direct listening mode is selected, the equalizer
settings have no effect.
• If “
Audyssey
” is enabled, it prevails over this setting
(
➔
page 52
).
THX Audio Setup
■
Surr Back Speaker Spacing
`
<1ft (<0.3m)
`
1ft-4ft (0.3m-1.2m)
`
>4ft (>1.2m)
You can specify the distance between your surround back
speakers.
Note
• Cannot be set if:
– “
Surround Back Ch
” is set to “
1ch
” (
➔
page 47
).
– “
Speakers Type(Front)
” is set to “
Bi-Amp
” (
➔
page 46
).
– “
Surround Back
” is set to “
None
” (
➔
page 47
).
– “
Powered Zone 2
” is set to “
Yes
” (
➔
page 46
) and Zone 2
turned on (
➔
page 65
).
■
THX Ultra2/Select2 Subwoofer
`
No
`
Yes
If you’re using a THX-certified subwoofer, set this setting
to “
Yes
”.
Note
• If the “
Subwoofer
” setting is set to “
No
”, this setting cannot be
selected (
➔
page 47
).
■
BGC
`
Off
`
On
You can apply THX’s Boundary Gain Compensation
(BGC) to compensate the perceived exaggeration of low
frequencies for listeners sitting very close to a room
boundary (i.e., wall).
Note
• This setting is only available if “
THX Ultra2/Select2
Subwoofer
” is set to “
Yes
”.
• If the “
Subwoofer
” setting is set to “
No
”, this setting cannot be
selected (
➔
page 47
).
■
Loudness Plus
`
Off
`
On
When the “
Loudness Plus
” is set to “
On
”, it is possible to
enjoy even subtle nuances of audio expression at low
volume.
This is only available when the THX listening mode is
selected.
■
Preserve THX Settings
`
Yes
`
No
If this setting is set to “
Yes
”, Dynamic EQ and Dynamic
Volume have no effect in THX listening mode.
Note
• This setting is fixed to “
Yes
” if “
Loudness Plus
” is set to “
On
”.
1
Press
w
to select “Channel”, and then use
e
/
r
to select a speaker.
2
Use
q
/
w
to select a frequency, and then use
the
e
/
r
to adjust the level at that frequency.
The volume at each frequency can be adjusted
from
–6dB
to
0dB
to
+6dB
in 1 dB steps.
Tip
• Low frequencies (e.g., 25Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use
q
to select “Channel”, and then use
e
/
r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “
No
”
or “
None
” in the “Speaker Configuration”
(
➔
page 47
).
THX Loudness Plus
THX Loudness Plus is a new volume control
technology featured in THX Ultra2 Plus™ and THX
Select2 Plus™ Certified receivers. With THX Loudness
Plus, home theater audiences can now experience the
rich details in a surround mix at any volume level. A
consequence of turning the volume below Reference
Level is that certain sound elements can be lost or
perceived differently by the listener. THX Loudness
Plus compensates for the tonal and spatial shifts that
occur when the volume is reduced by intelligently
adjusting ambient surround channel levels and
frequency response. This enables users experience the
true impact of soundtracks regardless of the volume
setting. THX Loudness Plus is automatically applied
when listening in any THX listening mode. The new
THX Cinema, THX Music, and THX Games modes are
tailored to apply the proper THX Loudness Plus settings
for each type of content.