47
En
Note
• If the “
Speakers Type(Front)
” setting is set to “
Bi-Amp
”,
Powered Zone 2 cannot be used.
• When the “
Powered Zone 2
” setting is set to “
Yes
”, the
surround back, front wide and front high speakers cannot be
used.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band
” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “
80Hz(THX)
” crossover.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the “
Audio TV Out
” setting is set to “
On
” (
➔
page 59
).
– “
HDMI Control(RIHD)
” is set to “
On
” (
➔
page 58
) and
you’re listening through your TV speakers.
■
Subwoofer
`
Yes
`
No
■
Front
`
Full Band
`
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
,
90Hz
,
100Hz
,
110Hz
,
120Hz
,
130Hz
,
150Hz
,
200Hz
Note
• If the “
Subwoofer
” setting is set to “
No
”, the “
Front
” setting is
fixed to “
Full Band
”.
■
Center
*1
, Surround
*1
, Surround Back
*2*
3
*4
`
Full Band
`
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
,
90Hz
,
100Hz
,
110Hz
,
120Hz
,
130Hz
,
150Hz
,
200Hz
`
None
■
Front Wide
*1*2*4
, Front High
*1*2*4
`
Full Band
`
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
,
90Hz
,
100Hz
,
110Hz
,
120Hz
,
130Hz
,
150Hz
,
200Hz
`
None
Note
*1
“
Full Band
” can be selected only when “
Full Band
” is
selected in the “
Front
” setting.
*2
If the “
Surround
” setting is set to “
None
”, this setting cannot
be selected.
*
3
If the “
Surround
” setting is set to anything other than “
Full
Band
”, “
Full Band
” cannot be selected here.
*4
If the “
Speakers Type(Front)
” setting is set to “
Bi-Amp
”, or
the “
Powered Zone 2
” setting is set to “
Yes
”, this setting
cannot be selected.
■
Surround Back Ch
`
1ch
:
Select if only one surround back speaker L is
connected.
`
2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “
Surround Back
” Setting is set to “
None
”, this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
`
80Hz
,
90Hz
,
100Hz
,
110Hz
,
120Hz
`
Bypass
:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
Note
• If you’re using THX-certified speakers, select “
80Hz
”.
■
Double Bass
`
On
`
Off(THX)
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to the
subwoofer.
Note
• This function can be set only if the “
Subwoofer
” setting is set to
“
Yes
”, and the “
Front
” setting is set to “
Full Band
”.
• If you’re using THX-certified speakers, select “
Off(THX)
”.
■
Subwoofer Phase
`
0º
`
180
º:
Moves the subwoofer phase.
Note
• If the “
Subwoofer
” setting is set to “
No
”, this setting cannot be
selected (
➔
page 47
).
This setting is set automatically by
Audyssey MultEQ
®
XT Room Correction and Speaker
Setup function (
➔
page 31
).
This setting is
NOT
set automatically by
Audyssey MultEQ XT Room Correction and Speaker
Setup function (
➔
page 31
).