22
700-398-01J X-Series User Manual Issued for version 2.8x
P rogrammable Output Code
This user property enables the use of various programmable outputs to perform home automation actions,
such as turning on lights, switches, motors, etc. Any event which is able to trigger a programmable output can
be assigned to an output number from 1 to 57. Assigning an event to outputs 1 to 5 will use the panel’s
onboard outputs 1 to 5. Assigning an event to outputs 6 to17 will use an output on a zone expander, 18-33 will
use an output on an output expander, 34-41 will use an output on a keypad, and 42-57 will use the Xwave
2
I/O
Modules. Refer to section 15.10 for details on using programmable outputs.
Assign a User Code to Partitions – Option 11 (Advanced)
LED Keypad
Hold down the [*] key until the beep, then enter [MASTER CODE] [*] [1] [1] [*] [USER CODE] [*] [PARTITION
No] [*] [#]
1.
Enter the User Program Mode as per steps 1 to 4 in section User Program Mode.
2.
Press the [1] [1] keys followed by the [*] key to select programmable option 11.
3.
The READY and ARM LEDs flash simultaneously.
4.
Enter the [USER CODE] followed by the [*] key.
5.
The READY and AWAY LEDs flash simultaneously, and the ARM LED will be on.
6.
The partitions to which the user code is assigned are displayed by the zone LEDs. If zone LED 1 is on, the
user code can arm or disarm partition 1. If zone LED 2 is on, the user code can arm or disarm partition 2.
It is possible to program codes to arm/disarm more than one partition.
7.
To select which partitions the user code may arm or disarm, toggle zone LEDs by entering the
[PARTITION No] followed by the [*] key. (LCD keypad press [*] again to turn N to Y or Y to N).
8.
The READY and AWAY LEDs flash simultaneously, and the ARM LED is on.
NOTE: To allocate a user to all partitions press the [0] key followed by the [*] key, when inputting the data for
the partition number.
9.
Repeat step 7 until the user code has been assigned to the correct partition(s).
10.
Press the [#] key to exit the current option.
11.
Press the [OPTION NUMBER] followed by the [*] key for the next option, or the [#] key again to exit user
programming.
LCD Keypad
[*] [MASTER CODE] [*] [1] [1] [*] [USER CODE] [*] [PARTITION NUMBER] [*] [*] [#]
1.
Enter the User Program Mode as per steps 1 - 4 of section User Program Mode.
2.
The LCD display reads ‘Option Menu’, ‘Add User Code’.
3.
To select menu option 11 – ‘User ->Partitions’, press the [1] [1] keys or alternatively use the [PANIC] or
[MED] keys to scroll through the list of programmable options until you reach the option you want.
4.
Press the [*] key.
5.
The LCD display reads ‘User Code + *’.
6.
Enter the [USER CODE] followed by the [*] key.
7.
The partitions to which the [USER CODE] is assigned are indicated by options 1 - 8. If the user is assigned
to partition 1, there will be a YES next to option 1 and the user can thus arm and disarm partition 1. If
the user is assigned to partition 4, there will be a YES next to option 4. It is possible to program codes to
arm/disarm any combination of the available partitions.
8.
Enter the [PARTITION NUMBER] followed by the [*] key. One may also use the [PANIC] and [MED] keys
to scroll through the partitions.
9.
Press the [*] key to toggle between YES and NO.
10.
Repeat steps 8 - 9 until the User Code has been assigned to the correct partition(s).
11.
Press the [#] key twice to exit the User Program Mode.
NOTE: When a new user is added, they are assigned to partition 1 by default. To change this, or to add them to
other partitions, requires that you program this option. If you do not add a user to a partition, they will not be
able to arm/disarm it.
