Infranor Xtracontrol DC2 User Manual Download

Page: 69 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

Disposal

The device contains the following components which need to be disposed of separately:



Metals



Electronic components



Battery

The following options are available for disposal of the device:

Disposal by the manufacturer

▶

At the end of the device’s life cycle you can return it to the manufacturer for a set fee. The manufacturer will

then deal with the recycling of the device.

Disposal in accordance with regional regulations

▶

Dismantle the device and disassemble it completely into its component parts.

▶

Send the metal parts for metal recycling.

▶

Sort the electronic parts (circuit boards, drives etc.).

▶

Dispose of the electronic scrap in accordance with the national laws and regulations.

▶

Check that the battery is fully discharged.

▶

Dispose of the battery in accordance with the national laws and regulations, via an authorised collection point.

Summary of Contents for Xtracontrol DC2
























































































Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands

Infranor Xtracontrol DC2, User Manual

Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands