Infranor Xtracontrol DC2 User Manual Download

Page: 57 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

The web configuration page will be displayed.

Fig. 43: list of web interface settings

Click on the “Network” link.

The “Network Configuration” page is displayed.

Fig. 44: “Network Configuration” page

Check the network settings and make any changes in the text boxes if required.

XtracontrolEC21 configuration: ETH0 = X4, ETH1 = X5

Save the settings by clicking on “Save”.

10.

Additional settings can also be viewed and/or modified on the web configuration page (e.g. system time,

display resolution, TargetVisu).

11.

In order to activate all of the modified settings, reboot the device:

Disconnect the device temporarily from the power supply
– or –
Click on “Reboot” in the web interface and then confirm on the next screen by clicking on “Reboot Module”.

The device is now configured and ready for use.

Summary of Contents for Xtracontrol DC2
























































































Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands

Infranor Xtracontrol DC2, User Manual

Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands