Infranor Xtracontrol DC2 User Manual Download

Page: 26 / 87

User Manual V1.3 | XtracontrolDC2, XtracontrolET2, XtracontrolEC21

4.3

Installation, XtracontrolEC21

The XtracontrolEC21 is designed to be installed on a mounting rail to DIN EN 60715:2001, 35 x 7.5 mm.

CAUTION

Danger of burns!

The surface of the device can become hot.

▶

Ensure that there is sufficient convectional cooling for heat to

dissipate.

▶

Ensure that there is also a minimum of 50 mm free space both

above and below the device.

Fig. 13: Installing the device

Requirements:



At least 1 cm free space must be left between the device and the adjacent module.

Insert the device into the mounting rail from above so that the clip is resting on the rail.

Push the device down against the mounting surface so that the retaining spring engages.

The device is now engaged on the mounting rail.

Infranor GmbH

Summary of Contents for Xtracontrol DC2
























































































Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands

Infranor Xtracontrol DC2, User Manual

Search results

Summary of Contents for Xtracontrol DC2

Reviews:

Related manuals for Xtracontrol DC2

Brands by name

Popular brands