Infortrend EonStor CS Maintenance Manual Download Page 56

Page: 56 / 133

EonStor CS Installation Guide

page 56 / 133

Installation Guide

1-8.4 How to replace Host Board

1. Please contact your reseller when there is some hardware component need to be replaced.

2. Please take note of the following considerations before replacing the host board:



A controller/host board downtime would be need if you replace a host board.



The controller would be set as factory default when adding or replacing a host board.

3. To replace the host board, you must remove the controller from enclosure. Loosen the screw that secure host

board to the controller, push the release lever and lift to remove the host board.

4. Use the guide pin to position the new host board to the host board slot, place it carefully (A) and fasten the thumb

screw to secure the host board in place (B). And then reinstall the controller back to the enclosure.

Summary of Contents for EonStor CS






































































































































Search results

Summary of Contents for EonStor CS

Reviews:

Related manuals for EonStor CS

Brands by name

Popular brands

Infortrend EonStor CS, Maintenance Manual

Search results

Summary of Contents for EonStor CS

Reviews:

Related manuals for EonStor CS

Brands by name

Popular brands