Infinova V3070-8 Series User Manual Download

Page: 82 / 90

Remote control battery power is low.

Remote control is damaged or device front panel is damaged.

21. Record storage period is not enough.

There are following possibilities:

Camera quality is too low. Lens is dirty. Camera is installed

against the light. Camera aperture setup is not correct.

HDD capacity is not enough.

HDD is damaged.

22. Can not playback the downloaded file.

There are following possibilities:

There is no media player.

No DXB8.1 or higher graphic acceleration software.

There is no DivX503Bundle.exe control when you play the file

transformed to AVI via media player.

No DivX503Bundle.exe or ffdshow-2004 1012 .exe in

Windows XP OS.

23. I forgot local menu operation password or network

password

Please contact your local service engineer or our sales engineer for

help. We can guide you to solve this problem.

24. There is no video. The screen is in black.

There are following possibilities:

IPC IP address is not right.

IPC port number is not right.

IPC account (user name/password) is not right.

25. The displayed video is not complete.

Please cheek current resolution setup. If the current setup is

1920*1080, then you need to set the monitor resolution as

1920*1080.

26. There is no HDMI output.

There are following possibilities:

Displayer is not in HDMI mode.

HDMI cable connection is not right.

27. The video is not fluent when I view in multiple-channel

mode from the client-end.

There are following possibilities:

The network bandwidth is not sufficient. The multiple-channel

monitor operation needs at least 100M or higher.

Your PC resources are not sufficient. For 16-ch remote monitor

operation, the PC shall have the following environment: Quad

Core, 2G or higher memory, independent displayer, display

card memory 256M or higher.

Daily Maintenance

Please use the brush to clean the board, socket connector and

the chassis regularly.

The device shall be soundly earthed in case there is audio/video

disturbance. Keep the device away from the static voltage or

induced 143H143Hvoltage.

Please unplug the power cable when you remove the

audio/video signal cable, RS232 or RS485 cable.

Always shut down the device properly. Please press the power

button in the front pane for at least three seconds to shut down

the device. Otherwise it may result in HDD malfunction.

Please make sure the device is away from the direct sunlight or

other heating sources. Please keep the sound ventilation.

Please check and maintain the device regularly.

Summary of Contents for V3070-8 Series



























































































Search results

Summary of Contents for V3070-8 Series

Reviews:

Related manuals for V3070-8 Series

Brands by name

Popular brands

Infinova V3070-8 Series, User Manual

Search results

Summary of Contents for V3070-8 Series

Reviews:

Related manuals for V3070-8 Series

Brands by name

Popular brands