Infinova V3070-8 Series, User Manual

Page: 54 / 90

46
Chapter VII Web Operation
7.1 General Introduction
The device web provides channel monitor menu tree, search, alarm
setup, system setup, PTZ control and monitor window.
Important
The following operation is based on 16-channel series device.
For the 32-channel series product, there is 32-channel option.
7.1.1 Preparation
Before log in, please make sure:
z
Network connection is right
z
NVR and PC network setup is right. Please refer to network
setup(main
z
menu->setting->network)
z
Use order ping ***.***.***.***(* NVR IP address) to check
connection is OK or not. Usually the return TTL value should
be less than 255.
z
Open the IE and then input NVR IP address.
z
System can automatically download latest web control and
the new version can overwrite the previous one.
z
If you want to un-install the web control, please run uninstall
webrec2.0.bat
. Or you can go to C:\Program Files\webrec to
remove single folder. Please note, before you un-install,
please close all web pages, otherwise the un-installation might
result in error.
z
Current series product supports various browsers such as
Safari, firebox browser, Google browser. Device only support
1-channel monitor on the Apple PC.
About PoE address setup, operation and allocation.
1) Insert PoE
After you insert PoE, device may try to set a corresponding IP
address of the Switch network adapter. First, system tries to set via
arp ping. It then uses DHCP if it finds the DHCP is enabled. After
successfully set IP address, system may use Switch to send out
broadcast, system thinks the connection is OK when there is any
response. Now system is trying to login the newly found IPC. Now
please check the interface, you can see the corresponding digital
channel is active now. You can see a small PoE icon at the top left
corner. You can see the PoE channel, PoE port information and etc
from the connection list of the remote device interface ( Section
5.6.11 ). For the IP search list, you need to click the IP search to
display or refresh.
2) Remove PoE
After you removed PoE, you can see the corresponding digital
channel becomes idle (disable). On the remote device interface, it is
removed from the connected list. For the IP search list, you need to
click the IP search to refresh.
3) After you insert PoE, system follows the principles listed
below to map channel.
a) If it is your first time to insert PoE, system can map it to the
first idle channel. After map, the channel can memorize the
MAC address of the IPC. It is a <Channel>---<IPC mac> map.
If current channel does not connect to other device, system
can memorize current MAC address, otherwise it can refresh
to the newly added device and memorize the <PoE
port>---<Channel>.
b) If it is your second time to insert the PoE, system can check
the saved MAC address according to <Channel>---<IPC
mac> map to make sure current IPC has connected or not. If
system finds the previous information and the channel is idle,
system can map it to the previously used channel. Otherwise
system goes to the next step.
c) Thirdly, according to the <PoE port>---<Channel> map,
system can know the previous mapping channel of current
PoE port. System can select current channel if it is free.
Otherwise, it goes to the next step:
d) Fourthly, system goes to find the first idle channel it can get.
Generally speaking, once you insert PoE, system follow the steps
listed above to find the channel available.
4) When you insert PoE, all channels are in use now.
System can pop up a dialogue box for you to select a channel to
overwrite. The title of the pop-up interface is the name of the
current operation PoE port. In this interface, All PoE channel
become grey and can not select.
7.1.2 Log in
Open the IE and then input the NVR IP address in the address
column.
For example, if your NVR IP address is 192.168.1.108, then please
input http:// 192.168.1.108 in IE address column. See Figure 7-1.