Inficon Sensistor ISH2000 HySpeed Operating Instructions Manual Download Page 52

Page: 52 / 54

Hydrogen leak detector Sensistor ISH2000 HySpeed

Operating Instructions

OP-Sensistor ISH2000 HySpeed-EN-201203

Disposal of product when taken out of service

According to EU legislation, this product must be recovered for
separation of materials and may not be disposed of as unsorted
municipal waste.

If you wish you can return this INFICON AB product to the
manufacturer for recovery.

The manufacturer has the right to refuse taking back products
that are inadequately packaged and thereby presents safety
and/or health risks to the staff.

The manufacturer will not reimburse you for the shipping cost.

Shipping address:
INFICON AB
Westmansgatan 49
582 16 LINKÖPING´
SWEDEN

Summary of Contents for Sensistor ISH2000 HySpeed























































Search results

Summary of Contents for Sensistor ISH2000 HySpeed

Reviews:

Related manuals for Sensistor ISH2000 HySpeed

Brands by name

Popular brands

Inficon Sensistor ISH2000 HySpeed, Operating Instructions Manual

Search results

Summary of Contents for Sensistor ISH2000 HySpeed

Reviews:

Related manuals for Sensistor ISH2000 HySpeed

Brands by name

Popular brands