background image

Hydrogen leak detector Sensistor ISH2000 HySpeed 

 - 

Operating Instructions

 

OP-Sensistor ISH2000 HySpeed-EN-201203

5

EN

1

 User information

Read this user manual carefully before using the Sensistor ISH2000 HySpeed.

1.1   Notes and safety notices

This manual contains warnings and cautions concerning the safe use of the product. 
See definitions below.

Note: A Note is used to indicate information that is important for trouble-free and 

optimal use of the Sensistor ISH2000 HySpeed.

1.2   Document outline

The document is devided in two main parts:

Getting started

Reference section

The Getting started part consists of step by step case examples, explaining how to 
use the Sensistor ISH2000 HySpeed in a variety common situations. The Reference 
section consists of in depth explanation and additional information, which 
completes the user manual with all relevant information.

1.3   Conventions used in this book

In this user manual the following text style (

hardware command

) is used for 

references to hardware commands or button labels, while this text style (

software 

command

) is used for references to software commands and menu choices.

WARNING!

Warning indicates a hazardous situation which, if not 
avoided, could result in death or serious injury. It is 
important not to proceed until all stated conditions 
are met and clearly understood.

CAUTION!

Caution indicates a hazardous situation which, if not 
avoided, could result in minor or moderate injury. It is 
important not to proceed until all stated conditions 
are met and clearly understood.

NOTICE!

Notice indicates instructions that must be 
followed to avoid damage to the Sensistor 
ISH2000 HySpeed or other equipment.

Summary of Contents for Sensistor ISH2000 HySpeed























































Reviews: