Inficon Sensistor ISH2000 HySpeed Operating Instructions Manual Download Page 47 | Manualshive

Page: 47 / 54

background image

Hydrogen leak detector Sensistor ISH2000 HySpeed

-

Operating Instructions

46

OP-Sensistor ISH2000 HySpeed-EN-201203

EN

11 Spare parts and accessories

There are a variety of spare parts and accessories to the Sensistor ISH2000 HySpeed.
In the following table some of these are presented, for a complete list of all spare
parts and accessories please visit

www.inficon.com

.

Table 11-1. Spare parts and accessories.

Part

Part no.

Combox (Box for controlling the gas sensor and signal processing)

590-820

Built-in Probe H65 (Connects to the instrument via Combox)

590-250

Hand Probe PK50 (Connects to the instrument via Combox)
Hand Probe PK50-Flex (Connects to the instrument via Combox)
Hand Probe P50 (Connects direct to the instrument)
Hand Probe P50-Flex (Connects direct to the instrument)
Robot Probe R50 (Connects to the instrument via Combox)

590-930
590-940
590-780
590-790
590-820

Probe Cable C21
Length 3m
Length 6m
Length 9m
Length 4m (Spiral)
Length 6m (Spiral)

590-161
590-175
590-165
590-163
590-164

Probe Tip Protection Cap for Hand Probes P50/PK50 and P50/PK50-
FLEX

Probe Tip Filter for Hand Probes (P50/PK50) and R50

590-625
(Set of 500)
591-234
(Set of 50)

591-234

Power cable eu
Power cable uk
Power cable us

591-146
591-147
591-853

Hand Probe sensor (fit K50/PK50/R50)

590-292

Mounting kit Sensistor ISH2000 HySpeed

590-810

Phoenix connector to Sensistor ISH2000 HySpeed

591-792

O-ring seal

591-528

Reference Leaks. Standard or customer specific leaks for detector
calibration

see separate
Data Sheet

«
...
45
46
47
48
49
...
»

Summary of Contents for Sensistor ISH2000 HySpeed























































Reviews:

No comments

Related manuals for Sensistor ISH2000 HySpeed

Brand: L-Sniper Pages: 12

Brand: NED Pages: 60

Brand: Panasonic Pages: 2

Gemini GEM-X255

Brand: NAPCO Pages: 40

Brand: NAPCO Pages: 16

Brand: NAPCO Pages: 6

Brand: VADDIO Pages: 20

WallVIEW CCU HD-18 HD-SDI

Brand: VADDIO Pages: 18

Brand: VADDIO Pages: 60

Brand: Vacron Pages: 2

CLEARVIEW HD-18

Brand: VADDIO Pages: 4

Brand: i-PRO Pages: 18

Brand: IFM Pages: 18

Brand: Wirepath Surveillance Pages: 2

Brand: Wiseup Pages: 24

Brand: Grundig Pages: 40

Brand: Q-See Pages: 31

Brand: Seas of Solutions Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands