11
1693 RLC Digibridge
Installation
1. Take the Digibridge to a qualified electronic
technician who has the necessary equipment
for minor disassembly and adjustment. Have
the electronic technician remove the interface
option assembly, as described in his 1693
Digibridge Service instructions.
There is no need to remove the top cover first.
2. Have the electronic technician set the
switches in “DIP” switch assembly S2 to
the desired address, which is a 5-bit binary
number. (See below.)
Figure 2-3: DIP switch set to Decimal Address 3
3. Have the electronic technician replace the
interface option assembly in its former place.
Notice that S2 is located at the end of the
interface option board, about 3 cm (1 in.)
from the TALK switch S1.
If S2 is covered
A. Lift the cover off, exposing the “DIP”
switch, which has 5 tiny switches, num-
bered 1 thru 5.
B. To enter logical 1’s, depress the side of
each switch nearest the end of the board
(switch open).
C. To enter logical 0’s, depress the other side
of the switch (switch closed). The address
is read from 5 to 1.
Thus, for example, to set up the address 00011,
enter 0’s at positions 5, 4, 3; enter l ‘s at
positions 2 and 1. (This makes the talk address
“C” and the listen address “#”.)
WARNING
Shock hazard and static electricity
can cause damage.
Disassembly should be preformed by
qualified personnel only.
Strictly speaking, the address includes more; S2
determines only the device-dependent bits of the
address. You cannot choose talk and listen addresses
separately, only as a pair. The list of possible pairs is
shown in Table 2-1.
The GPIB Address of the Digibridge is set by the
SW2 DIP Switch. The numeric value is set by setting
the switch on or off for the corresponding bit with
the OFF position for binary 1 and ON position for
binary 0. Depress the rocker toward the OFF mark-
ing for OFF and toward the numeric marking for the
corresponding ON position.
Decimal
Address
Switch Settings
S1
S2
S3
S4
S5
0
ON
ON
ON
ON
ON
1
OFF
ON
ON
ON
ON
2
ON
OFF
ON
ON
ON
3
OFF
OFF
ON
ON
ON
4
ON
ON
OFF
ON
ON
5
OFF
ON
OFF
ON
ON
6
ON
OFF
OFF
ON
ON
7
OFF
OFF
OFF
ON
ON
8
ON
ON
ON
OFF
ON
9
OFF
ON
ON
OFF
ON
10
ON
OFF
ON
OFF
ON
11
OFF
OFF
ON
OFF
ON
12
ON
ON
OFF
OFF
ON
13
OFF
ON
OFF
OFF
ON
14
ON
OFF
OFF
OFF
ON
15
OFF
OFF
OFF
OFF
ON
16
ON
ON
ON
ON
OFF
17
OFF
ON
ON
ON
OFF
18
ON
OFF
ON
ON
OFF
19
OFF
OFF
ON
ON
OFF
20
ON
ON
OFF
ON
OFF
21
OFF
ON
OFF
ON
OFF
22
ON
OFF
OFF
ON
OFF
23
OFF
OFF
OFF
ON
OFF
24
ON
ON
ON
OFF
OFF
25
OFF
ON
ON
OFF
OFF
26
ON
OFF
ON
OFF
OFF
27
OFF
OFF
ON
OFF
OFF
28
ON
ON
OFF
OFF
OFF
29
OFF
ON
OFF
OFF
OFF
30
ON
OFF
OFF
OFF
OFF
31
Not Used
Table 2-1: IEEE-488 address settings
Summary of Contents for RLC Digibridge 1693
Page 12: ...x Table of Contents 1693 RLC Digibridge This page is intentionally left blank...
Page 24: ...xxii 1693 RLC Digibridge Abbreviated Specifications This page is intentionally left blank...
Page 130: ...106 1693 RLC Digibridge Theory Figure 4 1 Block diagram of the 1693 RLC Digibridge...
Page 171: ......