IEI Technology ROCKY-6614 User Manual Download Page 81

Page: 81 / 204

-81

ROCKY-6614 CPU Card

DRAM Frequency [200*2 MHz]

The

DRAM Frequency

is not user configurable but reflects the DRAM frequency setting

after the

CPU/DRAM Frequency Ratio

(described above) has been set. This setting will

only appear when the

Auto Detect CPU and DRAM FREQU

BIOS option is disabled.

Clock Spread Spectrum [Disabled]

The

Clock Spread Spectrum

BIOS option can help to improve CPU EMI issues.

Disabled

(Default)

The clock spread spectrum is disabled

Enabled

The clock spread spectrum is enabled

5.3.2 IDE Configuration

The

IDE Configuration

menu (

BIOS Menu 4

) allows you to set or change the

configurations for the IDE devices installed in the system.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands