IEI Technology ROCKY-6614 User Manual Download Page 47

Page: 47 / 204

-47

ROCKY-6614 CPU Card

3.2.10 SATA Drive Connectors

CN Label:

SATA1, SATA2

CN Type:

1x7 pin port

CN Location:

See Figure 3-11

CN Pinouts:

See Table 3-13

The SATA drive ports provide connectivity to SATA drives with a maximum data transfer

rate of 150MB/s.

PIN

DESCRIPTION

PIN

DESCRIPTION

1 GND

5 RX-

2 TX+

6 RX+

3 TX-

7 GND

4 GND

Table 3-13: SATA Connector Pinouts

CAUTION!

Your SATA hard drives may come with both a 4P power connector and a SATA

power interface. Attach either the 4P connector or the included SATA power

cable to your SATA hard drives.

DO NOT

attach both the power connectors to

your SATA hard drives at the same time! Doing so will cause damage.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands