IEI Technology ROCKY-6614 User Manual Download Page 114

Page: 114 / 204

-11

CKY-6614 WSB- Card

114

IEI

Technology, Corp

snooping to be enabled, this option should be disabled.

PCI devices are informed that an ISA based Graphics

device is installed in the system so the ISA based

Graphics card will function correctly. This does not

necessarily indicate a physical ISA adapter card. The

graphics chipset can be mounted on a PCI card. Always

check with your adapter card manual first, before

modifying the default settings in the BIOS.

PCI IDE BusMaster [Disabled]

The

PCI IDE BusMaster

BIOS option allows you to enable or prevent the use of PCI IDE

busmastering. The Optimal and

Disabled

(Default) Busmastering

prevented

IDE controller on the PCI local bus has mastering

capabilities

OffBoard PCI/ISA IDE Card [Auto]

The

OffBoard PCI/ISA IDE Card

BIOS option allows you to select the OffBoard PCI/ISA

IDE Card to be selected.

Auto

(Default)

The location of the Off Board PCI IDE adapter card is

automatically detected by the AMIBIOS.

PCI Slot 1

PCI Slot 1 is selected as the location of the OffBoard

PCI IDE adapter card. Only select this slot if the

adapter card is installed in PCI Slot 1.

PCI Slot 2

PCI Slot 2 is selected as the location of the OffBoard

PCI IDE adapter card. Only select this slot if the

adapter card is installed in PCI Slot 2.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands