IEI Technology ROCKY-6614 User Manual Download Page 64

Page: 64 / 204

-64

CKY-6614 WSB- Card

IEI

Technology, Corp

Step 5:

Close the CPU socket.

Close the load plate and engage the load lever by

pushing it back to its original position. Secure the load lever under the

retention tab on the side of CPU socket.

Step 6:

After the cooling kit is installed

(see

Section 4.3.2

), connect the CPU cable to

the CPU 12V power connector.

Step 0:

4.3.2 Cooling Kit (CF-520) Installation

WARNING:

It is strongly recommended that you

DO NOT

use the original

heatsink and cooler provided by Intel on the ROCKY-6614.

The CPU board is vertically mounted on a horizontal backplane, and Intel’s

heatsink does not come with a support bracket on the soldering side, the

PCB may be bent by the weight of the cooling kit.

IEI’s cooling kit (CF-520) includes a support bracket that is combined with

the heatsink mounted on the CPU to counterweigh and balance the load on

both sides of the PCB.

Figure 4-5: IEI CF-520 Cooling Kit

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands