manualshive.com logo in svg

IEI Technology ROCKY-6614, User Manual

Share
Download
IEI Technology ROCKY-6614 User Manual Download Page 75

 

 

1

-75

ROCKY-6614 CPU Card 

75

 

o 

ID

:  

Installed BIOS ID 

o 

 

 

Processor

: Displays auto-detected CPU specifications 

o 

Type

: 

Names the currently installed processor 

o 

Speed

:  Lists the processor speed 

o 

Count

:  The number of CPUs on the CPU board   

o 

 

 

System Memory

: Displays the auto-detected system memory. 

o 

Size

: Lists 

memory 

size 

The 

System Overview

 field also has two user configurable fields: 

 

System Time [xx:xx:xx]

:

 

Allows you to set the system time.

 

 

System Date [Day xx/xx/xxxx]: 

Allows you to set the system date.

 

5.3 Advanced 

The 

Advanced

 menu (

BIOS Menu 2

) allows you to access CPU and peripheral device 

configuration options through the following sub-menus: 

 WARNING: 

Setting the wrong values in the sections below may cause the system to 

malfunction. Make sure that the settings you make are compatible with your 

hardware. 

 

 

CPU Configuration

 (see 

Section 5.3.1

) 

 

IDE Configuration

 (see 

Section 

　

) 

 

Floppy Configuration

 (see 

Section 5.3.3

) 

 

SuperIO Configuration

 (see 

Section 5.3.4

) 

 

Hardware Health Configuration

 (see 

Section 

　

) 

 

ACPI Configuration

 (see 

Section 5.3.6

) 

 

MPS Configuration

 (see 

Section 5.3.6.2

) 

 

Remote Access Configuration

 (see 

Section 5.3.8

) 

 

USB Configuration

 (see 

Section 0

) 

Summary of Contents for ROCKY-6614













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands