IEI Technology ROCKY-6614 User Manual Download Page 135

Page: 135 / 204

-13

ROCKY-6614 CPU Card

135

Enabled

Restore on AC Power Loss [Last State]

The

Restore on AC Power Loss

BIOS option allows you to specify what state the system

will return into if there is a sudden loss of power to the system.

Power Off

The system will remain turned off

Power On

The system will turn on

Last State

(Default)

The system will return to its previous state. If it was on,

it will turn itself on. If it was off, it will remain off.

Keyboard Resume Function [Disabled]

The

Keyboard Resume Function

BIOS option allows you to specify if the system will be

roused from a suspended or standby state when there is activity on the keyboard.

Disabled

(Default)

Wake event not generated by keyboard

activity

Any Key

Wake event generated when activity is

detected on any keyboard key

Specific Key

Wake event generated when activity is

detected on a specific keyboard key

Keyboard password

wakeup

Wake event generated when a keyboard

password is entered. If this option is

selected, a new BIOS option

Password

Key Enter

will appear underneath it.

Select this option, hit enter, and type in the

password.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands