IEI Technology ROCKY-6614 User Manual Download Page 96

Page: 96 / 204

-96

CKY-6614 WSB- Card

IEI

Technology, Corp

bi-directional communication between the system

and the parallel port device and the transmission

rates between the two are much faster than the

Normal mode.

ECP+EPP

The parallel port will operate in the extended

capabilities port (ECP) mode. The ECP mode

supports bi-directional communication between the

system and the parallel port device and the

transmission rates between the two are much faster

than the Normal mode

The parallel port will also be compatible with EPP

devices described above

Parallel Port IRQ [IRQ7]

The

Parallel Port IRQ

selection allows you to set the parallel port interrupt address.

IRQ5

IRQ5 is assigned as the parallel port interrupt address

IRQ7

EFAULT

) IRQ7 is assigned as the parallel port interrupt address

5.3.5 Hardware Health Configuration

The

Hardware Health Configuration

menu (

BIOS Menu 8

) allows you to change the

configuration for the H/W Health Function and shows you the operating temperature, fan

speeds and system voltages.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands