IEI Technology ROCKY-6614 User Manual Download Page 78

Page: 78 / 204

-78

CKY-6614 WSB- Card

IEI

Technology, Corp

Ratio CMOS Setting [18]

The

Ratio CMOS Setting

sets the ratio between the core clock and the FSB frequency.

The following configuration options are available:

NOTE:

If an invalid ratio has been entered to this field, BIOS will restore it to the

previous state.

Max CUPID Value Limit [Disabled]

NOTE:

If your OS is NT, this value must be set to enabled.

Disabled

(Default)

Disables legacy OSes that cannot support CPUs with

extended CUPID functions from booting up

Enabled

Enables legacy OSes that cannot support CPUs with

extended CUPID functions to boot up

Execute Disable Bit [Enabled]

The

Execute Disable Bit

configuration

option is a hardware configuration feature that

protects the CPU from a buffer overflow attack. It is recommended that you enable this

option.

Disabled

Forces the XD feature flag to always return to 0

Enabled

(Default)

Does not force the XD feature flag to return to 0

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands