IEI Technology ROCKY-6614 User Manual Download Page 109

Page: 109 / 204

-10

ROCKY-6614 CPU Card

109

The Onboard

SiS USB2.0 DEVICE

BIOS option allows you to enable or disable the

onboard SiS USB2.0 controller. If disabled, you will not be able to use USB2.0 devices on

the system.

Disabled

USB 2.0 interface is disabled and cannot be used.

Enabled

(Default)

USB 2.0 interface is enabled and can be used.

USB Configuration

The USB Configuration field shows the system USB configuration. The items listed are:

Module Version: x.xxxxx.xxxxx

USB Devices Enabled:

Lists the USB devices that are enabled on the system

Legacy USB Support [Disabled]

The

Legacy USB Support

BIOS option refers to USB mouse and USB keyboard support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard will not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded on the system.

Disabled (Default) Legacy

USB

support

disabled

Enabled

Legacy

USB

support

enabled

USB2.0 Controller Mode [HiSpeed]

The

USB2.0 Controller Mode

BIOS option allows you to set the speed of the USB2.0

controller.

FullSpeed

The controller is capable of operating at full speed

(12Mbits/second)

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Brands by name

Popular brands