IEI Technology ROCKY-6614 User Manual Download Page 124

Page: 124 / 204

-12

CKY-6614 WSB- Card

124

IEI

Technology, Corp

5.5.5 CD/DVD Drives

The

CD/DVD Drives

menu is similar to the

Removable Drives

BIOS Menu 21

and it

specifies the boot sequence of the available CD/DVD drives. When the menu is opened,

the CD drives and DVD drives connected to the system are listed as shown below:

1st Drive

[CD/DVD: PM-(part ID)]

2nd Drive

[HDD: PS-(part ID)]

3rd Drive

[HDD: SM-(part ID)]

4th Drive

[HDD: SM-(part ID)]

NOTE:

Only the drives connected to the system will be shown. For example, if only

two CDs or DVDs are connected only “

1st Drive

” and “

2nd Drive

” will be

listed.

You will then be able to select the boot sequence from the available devices. If you select

the “

1st Drive

” option a list of available HDDs will be shown. Select the first HDD you wish

the system to boot from. If you do not wish to boot from the “

1st Drive

” you may also

disable it.

5.6 Security

The

Security

menu (

BIOS Menu 22

) allows you to configure the system security settings

including passwords.

Summary of Contents for ROCKY-6614













































































































































































































Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands

IEI Technology ROCKY-6614, User Manual

Search results

Summary of Contents for ROCKY-6614

Reviews:

Related manuals for ROCKY-6614

Brands by name

Popular brands