IDT 8A3 Series Programming Manual Download Page 213 | Manualshive

Page: 213 / 340

background image

213

©2018 Integrated Device Technology, Inc

September 12, 2018

8A3xxxx Family Programming Guide

DPLL_CTRL_0.DPLL_HO_HISTORY_RESET

Reset advanced holdover history.

DPLL_CTRL_0.DPLL_FINE_PHASE_ADV_CFG

Configure the fine phase advance to be applied to the DPLL.

DPLL_CTRL_0.DPLL_PHASE_OFFSET_CFG Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

RESERVED

N/A

-

This field must not be modified from the read value

DPLL_PHASE_OFFSET_

CFG[35:0]

R/W

0

Signed 36-bit phase offset in ITDC_UIs.
ITDC_UI is input TDC unit interval. Please refer to the SCSR_INPUT_TDC
module for details on input TDC settings and ITDC_UI value. The default input
TDC settings yield 50ps ITDC_UI. A positive value here will cause an output
clock phase delay relative to the input clock phase and a negative value will
cause an output phase advance relative to the input clock phase.
Note that this phase offset configuration applies to both DPLL mode and write
phase mode.

Table 266: DPLL_CTRL_0.DPLL_HO_HISTORY_RESET Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_CTRL_0.DPLL_HO_HISTORY_RESET Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

019h

RESERVED[7:1]

HO_HISTOR

Y_RESET[0]

DPLL_CTRL_0.DPLL_HO_HISTORY_RESET Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

RESERVED

N/A

-

This field must not be modified from the read value

HO_HISTORY_RESET[0]

R/W

0

Reset advanced holdover history.
1 = enable reset, 0 = cancel reset. This bit is a self-clear bit. When the HO
history is cleared, this bit will be cleared to 0 by FW.

Table 267: DPLL_CTRL_0.DPLL_FINE_PHASE_ADV_CFG Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_CTRL_0.DPLL_FINE_PHASE_ADV_CFG Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

01Ah

FINE_PHASE_ADVANCE[7:0]

01Bh

RESERVED[15:13]

FINE_PHASE_ADVANCE[12:8]

«
...
211
212
213
214
215
...
»

Summary of Contents for 8A3 Series





















































































































































































































































































































































Reviews:

No comments

Related manuals for 8A3 Series

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: X-Micro Pages: 9

Brand: X-Micro Pages: 19

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

kontron KBox E-420-R1K/V1K

Brand: S&T Pages: 82

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Xmart Pages: 8

Brand: ZALMAN Pages: 8

Brand: Dahua Pages: 113

Brand: Xtreme Pages: 83

Serial Attached SCSI (SAS) Expander Card

Brand: Adaptec Pages: 26

Brand: Teridian Pages: 2

Xtreme Networked Boat

Brand: Broadband Products Pages: 16

Brand: MESA Electronic Pages: 27

ClareVision CV-M161620-04

Brand: Clare Controls Pages: 32

Brand: Behringer Pages: 12

Texas Instruments 6711 DSK

Brand: National Instruments Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands