IDT 8A3 Series Programming Manual Download Page 275

Page: 275 / 340

275

September 12, 2018

8A3xxxx Family Programming Guide

TOD_READ_SECONDARY_0.TOD_READ_SECONDARY

The maximum frequency of the clock driving the TOD accumulator is 1 GHz for DPLL 0 and 1, and 770 MHz for DPLL 2 and 3 .

TOD_READ_SECONDARY_0.TOD_READ_SECONDARY_COUNTER

This counter increments to indicate completion.

Table 368: TOD_READ_SECONDARY_0.TOD_READ_SECONDARY Bit Field Locations and Descriptions

Offset

Address

(Hex)

TOD_READ_SECONDARY_0.TOD_READ_SECONDARY Bit Field Locations

000h

SUBNS[7:0]

001h

NS[15:8]

002h

NS[23:16]

003h

NS[31:24]

004h

NS[39:32]

005h

SECONDS[47:40]

006h

SECONDS[55:48]

007h

SECONDS[63:56]

008h

SECONDS[71:64]

009h

SECONDS[79:72]

00Ah

SECONDS[87:80]

TOD_READ_SECONDARY_0.TOD_READ_SECONDARY Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

SECONDS[87:40]

R/O

Seconds part of TOD.
Unsigned 48-bit value in seconds.

NS[39:8]

R/O

Nanoseconds part of TOD.
Unsigned 32-bit value in nanoseconds.
The maximum value is 0x3b9ac9ff = 999,999,999 ns.

SUBNS[7:0]

R/O

Sub-nanoseconds part of TOD.
Unsigned 8-bit value in units of 1/256 nanoseconds.

Table 369: TOD_READ_SECONDARY_0.TOD_READ_SECONDARY_COUNTER Bit Field Locations and

Descriptions

Offset

Address

(Hex)

TOD_READ_SECONDARY_0.TOD_READ_SECONDARY_COUNTER Bit Field Locations

00Bh

READ_COUNTER[7:0]

Summary of Contents for 8A3 Series





















































































































































































































































































































































Search results

Summary of Contents for 8A3 Series

Reviews:

Related manuals for 8A3 Series

Brands by name

Popular brands

IDT 8A3 Series, Programming Manual

Search results

Summary of Contents for 8A3 Series

Reviews:

Related manuals for 8A3 Series

Brands by name

Popular brands