manualshive.com logo in svg

IDT 8A3 Series, Programming Manual

The IDT 8A3 Series programming manual is an essential resource for users seeking to maximize the functionality of their device. This comprehensive manual provides detailed instructions and guidelines for efficient programming, available for free download at manualshive.com. Unlock the full potential of your device with this user-friendly manual.

Share
Download
background image

134

©2018 Integrated Device Technology, Inc

September 12, 2018

8A3xxxx Family Programming Guide

INPUT_0.IN_MODE

Configure the electrical properties of this input and select the predefined DPLL loop filter configuration.

TRIGGER: Writing to this byte triggers a read and activation in hardware of all the bytes of the INPUT module.

Table 162: INPUT_0.IN_MODE Bit Field Locations and Descriptions

Offset 

Address 

(Hex)

INPUT_0.IN_MODE Bit Field Locations

D7

D6

D5

D4

D3

D2

D1

D0

00Dh

DPLL_PRED

[7]

MUX_GPIO_

IN[6]

IN_DIFF[5]

IN_PNMODE

[4]

IN_INVERSE

[3]

RESERVED[2:1]

IN_EN[0]

INPUT_0.IN_MODE Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

DPLL_PRED[7]

R/W

0

Select predefined configuration to be applied to DPLL when this input is 
selected, if predefined configuration is enabled in DPLL.
0 = pred0
1 = pred1

MUX_GPIO_IN[6]

R/W

0

Select a GPIO pin to mux into the input divider instead of the input pin. 
Only applicable to INPUT8-15. When set to 1, the following mapping applies:
GPIO0 pin -> INPUT8 
GPIO15 pin -> INPUT9
GPIO14 pin -> INPUT10 
GPIO13 pin -> INPUT11
GPIO12 pin -> INPUT12 
GPIO11 pin -> INPUT13
GPIO10 pin -> INPUT14
GPIO3 pin -> INPUT15
Applied only on a per input module basis (e.g. setting 
INPUT_8_INPUT_MODE_MUX_GPIO_IN results only in the GPIO0 pin being 
multiplexed into input divider 8).
0 = clock Input
1 = GPIO configured as input clock

IN_DIFF[5]

R/W

0

Select differential or single-ended input.
Only applicable to INPUT0-7. INPUT8-15 are always in single-ended mode. 
When set to 1, two input pins will be paired up as the differential inputs:
input pin 0 and 8 -> INPUT0 
input pin 1 and 9 -> INPUT1
input pin 2 and 10 -> INPUT2 
input pin 3 and 11 -> INPUT3
input pin 4 and 12 -> INPUT4 
input pin 5 and 13 -> INPUT5
input pin 6 and 14 -> INPUT6
input pin 7 and 15 -> INPUT7
0 = single-ended
1 = differential

Summary of Contents for 8A3 Series





















































































































































































































































































































































Reviews:

No comments

Related manuals for 8A3 Series

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Maco Standard Fitting Instructions Manual preview
Standard
Brand: Maco Pages: 38
F5 WANJet 500 Quick Start Card preview
WANJet 500
Brand: F5 Pages: 2
F5 ARX-500 Hardware Reference Manual preview
ARX-500
Brand: F5 Pages: 90
F5 ARX-4000 Parts Replacement Manual preview
ARX-4000
Brand: F5 Pages: 47
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Brand: Tandberg Data Pages: 2
Behringer EXPANSION CARD X-DANTE Quick Start Manual preview
EXPANSION CARD X-DANTE
Brand: Behringer Pages: 65
ekwb EK-FC Installation Manual preview
EK-FC
Brand: ekwb Pages: 2
Riverbed SteelCentral NetExpress Installation Manual preview
SteelCentral NetExpress
Brand: Riverbed Pages: 38
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
ZALMAN Extreme Gaming VGA Cooler GV1000 User Manual preview
Extreme Gaming VGA Cooler GV1000
Brand: ZALMAN Pages: 7
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
Belden HIRESCHMANN IT MAMMUTHUS MTM8003-FAN User Manual preview
HIRESCHMANN IT MAMMUTHUS MTM8003-FAN
Brand: Belden Pages: 84
OWC Mercury FireWire 400 Owner'S Manual preview
Mercury FireWire 400
Brand: OWC Pages: 2
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Brand: Promise Technology Pages: 26
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
ICS ELECTRONICS VXI-5501 Quick Start Manual preview
VXI-5501
Brand: ICS ELECTRONICS Pages: 4

Brands by name

Popular brands

Load more brands