IDT 8A3 Series Programming Manual Download Page 212

Page: 212 / 340

212

September 12, 2018

8A3xxxx Family Programming Guide

DPLL_CTRL_0.DPLL_PRED1_PSL

Predefined configuration 1 loop filter phase slope limit.

DPLL_CTRL_0.DPLL_PHASE_OFFSET_CFG

DPLL phase offset configuration.

DPLL_CTRL_0.DPLL_PRED1_BW Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

BW_UNIT[15:14]

R/W

DPLL loop filter bandwidth unit.
0 = uHz
1 = mHz
2 = Hz
3 = kHz

DPLL_PRED1_BW[13:0]

R/W

Unsigned 14-bit DPLL loop filter bandwidth value.

Table 264: DPLL_CTRL_0.DPLL_PRED1_PSL Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_CTRL_0.DPLL_PRED1_PSL Bit Field Locations

012h

DPLL_PRED1_PSL[7:0]

013h

DPLL_PRED1_PSL[15:8]

DPLL_CTRL_0.DPLL_PRED1_PSL Bit Field Descriptions

Bit Field Name

Field Type Default Value

Description

DPLL_PRED1_PSL[15:0]

R/W

Unsigned 16-bit loop filter phase slope limit in ns/s.
Value 0 implies no phase slope limit.

Table 265: DPLL_CTRL_0.DPLL_PHASE_OFFSET_CFG Bit Field Locations and Descriptions

Offset

Address

(Hex)

DPLL_CTRL_0.DPLL_PHASE_OFFSET_CFG Bit Field Locations

014h

DPLL_PHASE_OFFSET_CFG[7:0]

015h

DPLL_PHASE_OFFSET_CFG[15:8]

016h

DPLL_PHASE_OFFSET_CFG[23:16]

017h

DPLL_PHASE_OFFSET_CFG[31:24]

018h

RESERVED[39:36]

DPLL_PHASE_OFFSET_CFG[35:32]

Summary of Contents for 8A3 Series





















































































































































































































































































































































Search results

Summary of Contents for 8A3 Series

Reviews:

Related manuals for 8A3 Series

Brands by name

Popular brands

IDT 8A3 Series, Programming Manual

Search results

Summary of Contents for 8A3 Series

Reviews:

Related manuals for 8A3 Series

Brands by name

Popular brands