IDEAL EVO S 50 Installation And Servicing Download

Page: 87 / 136

27.08.2018

87 / 136

EVO S -

Installation and Servicing

Line No. Value

Check the sensor values

B3 DHW sensor

DHW temp B3/B38

(7750)

in °C

• Configuration

menu

Check the hydraulic diagram

Check no. heat source 1

(6212)

Check no. heat source 2

(6213)

Check no. storage tank

(6215)

Check no. heating circuits

(6217)

G. CONFIGURATION OPTIMISATION

DHW optimisation:

•

DHW tank

Adjust the over value

Flow setpoint boost

(5020)

16 °C

Maintenance optimisation

A maintenance message may be generated that does not set the boiler to fault. This maintenance

message may be displayed after the following 3 counters have expired:

•

Time since last maintenance (or commissioning): set parameter 7044 to 12 months.

•

Operating hours of the burner (parameter 7040).

•

Number of starts (parameter 7042)

These last 2 parameters are dependent on the boiler's hydraulic installation. We recommend

using at least parameter 7044 for annual maintenance.

Diagram: VF24

page 4 / 4

Summary of Contents for EVO S 50









































































































































Search results

Summary of Contents for EVO S 50

Reviews:

Related manuals for EVO S 50

Brands by name

Popular brands

IDEAL EVO S 50, Installation And Servicing

Search results

Summary of Contents for EVO S 50

Reviews:

Related manuals for EVO S 50

Brands by name

Popular brands