2-3
2
TABLE 2-1 N4865A CONFIGURATION SETTINGS
Setting Choices
Comments
Setting Choices
Comments
Setting Choices
Comments
IP Address Mode Static or
Static lets the user set the N4865A’s IP Address, Net
Static or
Static lets the user set the N4865A’s IP Address, Net
Static or
Static lets the user set the N4865A’s IP Address, Net
DHCP
Mask and Gateway IP values. DHCP enables the
DHCP
Mask and Gateway IP values. DHCP enables the
DHCP
Mask and Gateway IP values. DHCP enables the
N4865A to accept the IP values supplied by a DHCP
Server. If there is no Server, the N4865A defaults
to IP address 169.254.48.65 and Net Mask of
255.255.0.0. The factory setting is DHCP.
IP Address
Any
Sets the N4865A’s own IP address. Any valid IP
IP Address
Any
Sets the N4865A’s own IP address. Any valid IP
IP Address
Any
Sets the N4865A’s own IP address. Any valid IP
address setting. Must be four groups of numbers
between 0.0.0.0 and 255.255.255.255. The default for
between 0.0.0.0 and 255.255.255.255. The default for
static assignments is 192.168.0.254 .
Net Mask
Any
254.254.0.0. for B range operation.
Net Mask
Any
254.254.0.0. for B range operation.
Net Mask
Any
254.254.0.0. for B range operation.
Gateway IP
Any
Set to match the static IP. Recommend using 1 for the
Gateway IP
Any
Set to match the static IP. Recommend using 1 for the
Gateway IP
Any
Set to match the static IP. Recommend using 1 for the
last octet. i.e. 192.168.0.1.
IP KeepAlive
On or Off Enables the N4865A’s socket layer to send the client a
On or Off Enables the N4865A’s socket layer to send the client a
On or Off Enables the N4865A’s socket layer to send the client a
short test message after 120 minutes if there has been
no activity on the socket. If the client fails to reply,
the N4865A will close the socket, release any locks
and reclaim all associated oscilloscope links. Do not
enable Keep Alive if the network or the client does
not support Keep Alive messages. Factory setting is
On.
N4865A’s GPIB 0 to 30
Sets the GPIB address the N4865A uses for itself on
0 to 30
Sets the GPIB address the N4865A uses for itself on
0 to 30
Sets the GPIB address the N4865A uses for itself on
Address
the GPIB bus. Values are 0 to 30. Recommended
Address
the GPIB bus. Values are 0 to 30. Recommended
Address
the GPIB bus. Values are 0 to 30. Recommended
values are 0 and 21. Factory setting is 4.
Instrument IP
Any
Sets the oscilloscope’s IP address. Not required if
Instrument IP
Any
Sets the oscilloscope’s IP address. Not required if
Instrument IP
Any
Sets the oscilloscope’s IP address. Not required if
AutoFind is On. If AutoFind is Off, the N4865A will
look for an oscilloscope at just this IP address. The
oscilloscope IP address can be any valid IP address
setting between 0.0.0.0 and 255.255.255.255. The
default value is: 192.168.0.200.
AutoFind
On or Off Enables the N4865A to ignore the Oscilloscope IP
On or Off Enables the N4865A to ignore the Oscilloscope IP
On or Off Enables the N4865A to ignore the Oscilloscope IP
address setting and search for a VXI-11.3 compatible
oscilloscope in the N4865A’s B address range. The
N4865A will attempt to open channels and link to
the fi rst oscilloscope it fi nds. Enable AutoFind for
back-to-back connections only. Disable AutoFind
when connecting to the oscilloscope over a network.
Factory setting is On.
Note: Default values are listed in Table 1-2
Summary of Contents for N4865A
