manualshive.com logo in svg

Icom AP-3, Instruction Manual

Share
Download
Icom AP-3 Instruction Manual Download Page 87

SPECIFICATION

17

79

■

LAN card (SL-1100 and SL-1105)

• Wireless Medium

: Direct Sequence Spread Spectrum (DSSS)

• Network Standard

: Based on IEEE 802.11b

• Frequency Band

: 2400 – 2483.5 MHz

• Number of channels

: 11

• Modulation

: DBPSK at 1 Mbps

DQPSK at 2 Mbps
CCK at 5.5 and 11 Mbps

• Encryption

: 64-bit or 128-bit WEP

• Output Power

: ±20 mW

• Frequency Stability

: 20 ppm (0°C to +50°C; +32°F to +122°F)

• Antenna

: Dual pattern antenna with diversity support

• Sensitivity

: More than –76 dBm (FER 8% at 1024 octets data)

• Power supply requirement

: (SL-1100) 5 V DC ±5% (negative ground)

(SL-1105) 3 V DC ±5% (negative ground)

• Current drain

: Transmit 290 mA

Receive 210 mA

• Usable temperature range

: 0°C to +50°C; +32°F to +122°F

• Dimensions (projections not

: 

included)

• Weight

: Approx. 40 g; 14 oz

• Approval standard

: FCC Part 15, Sub Part B, Class B, Part 15.247

• Media Access Protocol

: Carrier Sense Multiple Access with Collision

Avoidance (CSMA/CA)

• Host interface

: PCMCIA Type II slot

• Network operating system

: Microsoft® Windows® 2000/NT/98/95

Summary of Contents for AP-3



























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands