background image

4-10

Installing Memory, the Avid Board Set, and the Fan Kit

Moving the Adaptec 29160LP SCSI Controller Board

The Adaptec 29160LP SCSI controller board is a single-channel Ultra3 
controller that ships with the system in PCI slot 5. You must remove 
the board from PCI slot 5 and place it in PCI slot 1. 

The Adaptec 29160LP SCSI controller board supports Low-Voltage 
Differential (LVD) peripherals in two locations:

The system drive in drive bay 7.

LVD drives that connect externally to the very-high-density 
connector located on the boards metal PCI bracket.

n

Avid only supports LVD drives off the external connector of the Adaptec 
29160LP SCSI controller board.

Installing the Optional PCI Disk Controllers

This section describes installation and configuration requirements for 
the optional PCI disk controllers supported on the IBM 6868 system. 
The following devices are detailed:

ATTO Technology ExpressPCI UL3D/160 Dual-Channel LVD

Emulex LP850 Fibre Channel 

Using Table 4-1 on page 4-5, install the disk controllers in the proper 
slots using the descriptions provided in the following sections.

Summary of Contents for IntelliStation M Pro 6868-5BU



















































































































Reviews: