IAI EC ELECYLINDER EC-GD4 Instruction Manual Download | Manualshive

Page: 52 / 208

background image

1-23

1. Specifications

[Pressing Force and Current Limit Value]

Caution

The relation of the current limit and the pressing force is a guideline at speed of
20mm/s.
There is some variance in the actual pressing force. The variance increases when the
current value is low.
The current limit value cannot be set outside the 20 to 40% range.
When the approach speed up to the pressing start position is 20mm/s or less, pressing
operation will take place at approach speed. When the pressing speed is 5mm/s or
more and less than 20mm/s, it may not satisfy the pressing force shown in the graph
(reference). Confirm in advance that there is no problem in the pressing force.
Also when the pressing speed is less than 5mm/s, the pressing force and the operation
may get unstable. Make sure that the speed is set at 5mm/s or more.

1.2 Mechanical specifications

Pressing Force [

N

]

Current Limit Value [%]

Lead 2

Lead 4

Lead 6

«
...
50
51
52
53
54
...
»

Summary of Contents for EC ELECYLINDER EC-GD4

















































































































































































































Reviews:

No comments

Related manuals for EC ELECYLINDER EC-GD4

Brand: VADDIO Pages: 2

Brand: Parker Pages: 12

Brand: LLURIA Pages: 2

Brand: Baier Pages: 20

Brand: Tamiya Pages: 5

Brand: SAGEMCOM Pages: 2

Brand: Instant Care Pages: 2

Soluna Remote Control

Brand: Rollei Pages: 8

Brand: TSM Pages: 2

Devicenet R7F4HD-DAC32C

Brand: M-system Pages: 9

Brand: Universal Remote Pages: 10

Brand: Consort Pages: 4

Brand: Carel Pages: 2

Brand: Eaton Pages: 2

Brand: ZKTeco Pages: 27

TITAN CONTROLS KRONUS 2

Brand: Sunlight Supply Pages: 4

Brand: Zamel Pages: 2

iMO-LEARN - MDM

Brand: i3-TECHNOLOGIES Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands